The PTF-COMBO-100 120v Powder-To-Film system (patent pending), also known as a Powder Shaker, uniformly coats DTF films with adhesive powder, improving DTF printing performance and operator safety. Instead of hand-coating DTF films in open plastic containers that expose shop personnel to adhesive dust and require operator time and attention to obtain reliable results, the PTF-100 system provides uniform coverage without dusting and spillage, reducing waste and freeing staff to optimize production time.

Purpose-built for DTF printing, the tabletop unit consists of a steel enclosure on a stand, with a clear polycarbonate door set at an angle. It comes with two identical cartridges, each of which can hold approximately 3 lbs (1.4 kg) of adhesive powder. It has a rear mounted exhaust designed to collect adhesive dust particles and create a “negative pressure” condition within the cabinet. The film tray is suspended on special rubber hangers that isolate it from the intense vibration applied to remove excess powder from the film.

To operate, a filled cartridge is inserted at the top of the unit, and an empty cartridge at the bottom. An operator positions the wet DTF printed film on the application tray, print side up. Once the polycarbonate door is closed tightly, the operator adjusts the amount of powder released by the duration and number of times the release handle is activated.

The top cartridge releases adhesive powder which rains down on the film, ensuring complete and even coverage. After the film is coated to the satisfaction of the operator, the actuator is depressed to start a timed vibration cycle to release any
excess powder from the film. When empty, the upper cartridge can be switched quickly and cleanly with the lower cartridge containing all excess powder, reducing exposure while eliminating waste and allowing continuous production until refilling is needed.

Made in the USA, the PTF-100 can accommodate film sizes up to 16 x 20 in. (406 to 508 mm).

The PTF-100 Powder-To-Film system pairs well with a Vastex D-100 or D-1000 tabletop conveyor dryer equipped with rear mounted powered exhaust hood to vent glycol fumes from the shop environment. Vastex also offers heat presses and sturdy mobile utility stands that can accommodate most DTF equipment to optimize the shop floor layout.

ECONOMICAL
Interchangeable cartridges minimize waste, offers quick and clean refills.

VERSATILE
Fits up to 16 x 20 in. films

CONSISTENT
Both the angle of powder deflection and timer are adjustable for repeatable results

STURDY
Powder-coated stainless steel case and polycarbonate door for years of use

DUST-FREE
Sealed for mess-free operation

Flat top to fit Vastex PTF-100 Powder-To-Film System, and can also accommodate other compact tabletop equipment weighing up to 250 lb (113 kg).
26.8 in. (68 cm) H x 32.3 in. (82 cm) W x 32.3 in. (82 cm) D
55 lbs (25 kg)
Shippable via UPS

D-100 Dryer

Entry level tabletop dryer with 18″ (45.7 cm) wide conveyor belt cures up to 110 plastisol-printed garments/h, 50 discharge-printed garments/h, and DTF adhesives at high rates. Adjustable heater height/angle, heat intensity and belt speed provide full operator control.

SMART
Teflon coated fiberglass belt with tracking system

BELT WIDTH
(max garment width)
18″ (46 cm)

HEATER WIDTH
16″ (41 cm)

ADJUSTABLE
Speed, temperature, heater height and tilt

FAST
110+* shirts per hour with plastisol and 50+* with discharge

PRECISE
Powerful infrared heater with tight coil pattern and heat shields

VALUABLE
Best warranty, high quality, exceptional service

COMPACT
Total footprint is less than 8 sq.ft (2.44 sq.m)

OPTIONS

Optional powered exhaust removes moisture and fumes — ideal for working in confined spaces.
Exhaust hood (EXH-18)
Optional stands with wheels